![install cr4 nand x jasper install cr4 nand x jasper](https://jamesledger.net/content/images/2021/02/IMG_0392.jpg)
![install cr4 nand x jasper install cr4 nand x jasper](https://i.ytimg.com/vi/5Liw1TtwoOU/maxresdefault.jpg)
Luckily it is the big one and I can resolder it back without any issue. I also managed to knock a capacitor from the back of the CPU when reinstalling the xclamp lol. While the console is open, I decided to repaste the CPU, and add some 1.5cmx1.5cm heatsinks to the southbridge (because it is hot for my consoles) and the hana chip, which is not that hot. Other timing files that I tested won't boot the console. And yes, I bought 2 fake Ace V3s, and both only work with T60.9. I used the L0.3T60.9 timing file and it is booting consistently within less than 10 seconds. I bought the cheapest AceV3 (which is a fake I think) that I can find.ĭuring the installation, I had to reflash the firmware of my J-R Programmer v2 because it was randomly not working with the firmware that it came with.Īlso, I noticed that the fake AceV3s that I got do not want to glitch with common best timing files. Use the RGH 1.2 guide that I linked below and use the timing files from the guide.Yesterday I got my chips from eBay. Use isopropyl alcohol 71% > to clean up the flux. Cut the end of the wires short and no solder blobs. ***The other soldering problems are RST, POST, and ground (black wire). I linked the Rev C diagram for RGH 1.2 and a picture of how I prepped my awesome clone Rev C chip. RGH 1.2 falls under RGH1 and therefore 3-2 jumper has to be bridged as well.RGH 1.2 falls under RGH1 and therefore JP jumper has to be bridged.CAP jumper pads have to be bridged (closed/enabled) because its required for Jaspers.There are three steps that you have to take with the Rev C and also because you're working with a jasper. Looking at your soldering pictures tells me that its all about your work instead of the glitch chip. I'm changing the thermal paste on this one and will then put this baby into a Halo 3 Edition case. Might not be kosher but it instaboots everytime now, magical.Īlso I put in my first chip again where JP, 2-3 and CAP was bridged since datsmydrpepper pointed it out and no more flashing green light. Matter is resolved! Octal450 recommended new wiring which I did, two new pictures at the end of the album. The CR I installed on a trinity with SRGH works best out of all the Xboxes I've modded though, fastest boot times. One out of the 4 CR I ordered couldn't even be programmed with timers so maybe it's a shitty batch. Tried bridging CAP on the CR but that makes the chip go bananas, flashing green like it's resetting the xbox all the time. Tried different timers (15-24) but at most I get one instaboot and the rest take from 40-90 seconds.
INSTALL CR4 NAND X JASPER INSTALL
I followed the weekend modder's tutorial on rgh 1.2 for wiring and points, translating his matrix points to coolrunner. Completely new method and design 5-wire install up to 4x faster code than previous versions Supports all PHAT Falcon & Jasper Supports all SLIM Trinity. Using coolrunner rev c (Chinese crap clone) and tried replacing it with another clone. My first Jasper RGH and the boot times are worse than my trinites and corona I've modded. Homebrew applications and hacks are not limited to piracy, and it opens the door to legal threats and irritation. NOTE: Please don't use this subreddit as a hub for piracy. Please use the search function and refer to the FAQ above before asking about compatibility or how a system can be exploited. Buying, selling, and trading of items on this subreddit is strictly prohibited for the protection of users. that may contain links to things of that nature - however - are permitted. Please do NOT direct link to anything that violates copyright laws. FAQ / Wiki and Tutorials Xbox Homebrew DiscordĪnything and everything related to Xbox 360 hacking! News, releases, and questions regarding Xbox 360, Xbox One, and future Xbox homebrew.